Standard Instructions of Pasting Ricon Head Flat Cables

理光喷头排线的粘贴作业指导书及标准
Standard Instructions of Pasting Ricon Head Flat Cables
一：由于粘贴对象属于贵重喷头，所以首先需要构造一个无尘布桌面，以及各种所需工具，如图（2-1）。喷头需轻拿轻放。
First a non-dust desk surface and tools below are needed (seen photo 2-1). The print head must be handled with care.
1.剪刀*1pcs
2.喷头若干
3.3J抗干扰屏蔽隔离电磁波防辐射银灰色平纹单面胶*1卷（50mm宽）
4.3J布基胶带*1卷（100mm宽）
1. 1x scissors
2. A number of print heads
3. 1x single-side adhesive 3J
4. 1x duct tape (100mm )

2-1

二：抗干扰胶布的裁剪与粘贴
To cut our and paste with single-side adhesive
1.首先截取抗干扰胶布长度320mm 大致与喷头排线矩形部分长度相同（如图2-2 2-3）。
First cut out 320mm-long single-side adhesive, similar to the length of the flat cables (Seen 2-2 2-3 ).

2-2

2-3

2.然后将抗干扰胶布撕开，平摊于桌面上，并且将喷头排线矩形部分左右前后均分粘贴与抗干扰胶布上（如图2-4），注意粘贴平整，接着从胶布中间开始翻折粘贴，粘贴过程中，不能有特别明显的褶皱。
Second, tear the single-side adhesive, put on the desk surface, and paste the print head flat cable on it(Seen 2-4). Smooth adhesive is necessary.

2-4

3.粘贴完成后（如图2-5），将喷头排线翻转根据2的方式粘贴另一边至（如图2*6 2-7）
Third, fold the flat cable to be pasted another surface (Seen 2-6, 2-7).

2-5.

2-6

2-7

4.粘贴过程中，喷头千万得把持好，建议姿势参考（如图2-8）
While pasting, the way to hold the print head is suggested as Photo 2-8.

2-8
三:布基胶带的裁剪与粘贴
To cut out and paste with duct tape
1.将粘贴好抗干扰胶布的喷头排线一端粘贴上布基胶带，慢慢粘贴至另一端，确定长度，剪下布基胶带（如图2-9）
First, paste onto the duct tape and cut out proper length (Seen 2-9).

2-9

2.然后将布基胶带依然从中间开始，向两端翻折粘贴，必须无特别明显褶皱（如图2-10）
Second, fold and paste from the middle part to the side. No obvious distortion (Seen 2-10).

2-10

3.接着，将剩下的布基胶带翻折至完全粘贴完成（如图2-11），粘贴过程中，布基胶带总长度需稍微长于抗干扰胶布，达到两端完全覆盖抗干扰胶布（如图2-12）。
Third, fold and paste the rest part. The total length should be longer than single-side adhesive to make it full covered (Seen 2-12).

2-11

2-12

4.根据现场要求，喷头数量来粘贴，粘贴过程中，由于会用到剪刀等锋利工具，需要注意自己和他人的安全，以及喷头排线的安全，做到胆大心细。
Fourth, be aware of safe operation.
5.全部粘贴完成后，对粘贴过程中产生的垃圾进行适当的处理。
Fifth, handle the waste properly.

What are the precautions for the print head operation of universal printer ?

The using of UV flatbed printer need to train and standard. Because the print head of the UV flatbed printer is easy to damage and block.Therefore,we need to pay attention to the operation and the using of  auxiliary parts when we using the print head.Otherwise once hurt print head,it  will cause a certain loss and difficult to make up for the loss. This is why Maxcan have a free train to tell you how to use and maintain the UV flatbed printer.

Although , the operation way of UV flatbed printer is easy now. Almost entirely for computer software Operation, the method is very simple. However ,you still cannot be careless and random operate. Because the  flatbed printer is very large machinery, internal system is very complex. It will make uv flatbed printer out of order such as cannot answer and cause crash regardless if operation is not standard or multi-tapping or operating multiple functions in a short time.These operations make the print head in the printing status but have not for printing work, it is easy to damage the print head.

Besides,we need to clear the print head in the flatbed printer to print before and after work. You cannot use the normal paper or cloth to wipe when cleaning. Otherwise it is very easy to make the print head with dust and fiber, which leads to the print head clogging.

Second, we should pay attention to choose the auxiliary parts of flatbed printers.

Flatbed printer is excellent manufacture, which not install a useless parts.Therefore,do not remove any parts on the flatbed printer, often check and firm the parts of flatbed printers  installation. Do not  let the wires off from machine or loose.Especially air filter of the ink tank, deputy ink tank, these easily mixed with all kinds of dust particles and will ink pollution.It will produce the wear for print head and parts of print head.

Some manufacturer has a earthed wire and heat sink in the print head of flatbed printer. It can effectively eliminate static grounding line electricity and prevent the nozzle be worn or dust adsorption.When the working time of flatbed printer nozzle is slightly longer, please pay attention to the nozzle temperature and ensure the normal work of the heat sink.

The last but not least, the earthed wire facility of flatbed printer must be ensure perfect .It will produce electrostatic in work shop due to particles invisible air friction. The electrostatic for every system environment of flatbed printer are huge great damage.

Shenzhen Maxcan intelligent carriage lifting elevator techniques will solve these problems effectively. Intelligent carriage elevator can according to the thickness of the material  automatic relize the memory lift adjustment, to ensure that the nozzle is apart from the material with a  ideal height and the characteristics of  the rise and fall of stability, accurate positioning, deft and agile.Thereby reducing the print error effectively